Feel free to browse our blog The Manual Edger. Discover here the honest product review you have been looking for about Black 18v Cordless Electric.
 BLACK & DECKER 18 VOLT ELECTRIC CORDLESS GRASS BLOWER SWEEPER 18V RECONDITIONED US $52.00 
|
 Black & Decker Grass Hog 12" 18V Cordless Electric String Trimme w/ 2 Batteries US $203.26
|
 Black & Decker Pro Grass Hog 12" 18V Cordless Electric String Trimmer Edger US $95.53
|
 New Cordless Electric Pole Chainsaw Black & Decker 18V US $155.99
|
 Black & Decker NST2118R 18V Cordless 12" Electric Grass Lawn Trimmer Edger US $71.95
|
 Black & Decker CCS818 18V Cordless Electric Chain Saw US $114.99
|
 New Cordless Electric Chainsaw Black & Decker 18V US $119.99
|
 Black Decker Grass 12" 18 V Cordless Electric String Trimmer Edger Cut Power NEW US $153.89
|
 Black & Decker NST2118 12-Inch 18V Cordless Electric String Trimmer US $92.46
|
 Black & Decker CCS818 18-Volt Cordless Electric Chain Saw 18V US $89.99
|
 Black Decker 18 V Cordless Electric Broom Hard Surface Sweeper Vacuum Leaf NEW US $121.49
|
 Black & Decker 12-Inch 18V Cordless Electric String Trimmer with 2 Batteries US $87.99
|
 NPP2018 Black & Decker 18V Cordless Electric Pole Saw US $134.99
|
 BLACK & DECKER 18 VOLT CORDLESS ELECTRIC BLOWER 125 MPH SURFACE SWEEPER 18V US $32.95
|
 Black & Decker 18-V Cordless Electric Garden Cultivator US $119.99
|
Black 18v Cordless Electric
Black & Decker CCC3000 18-Volt Cordless Electric Lawncare Center.
Tips To Revive An 18V Drill Battery
-
Test your dead cordless drill battery pack using the volt meter to verify which lead in your battery case is negative and which is positive. Clearly mark which point is positive and which is negative on the battery case to ease the difficulty of later reassembly.
-
Use a small screwdriver to open the drill battery case. Watch out for the spring inside of the case because it tends to pop out and can easily get lost. Save the screws and spring by placing them in a small container.
-
Lift off the top of the cordless drill battery case to expose the inner battery cells. These cells will look like a grouping of C batteries that are joined together in one link.
-
Remove the battery cells from within the bottom of the drill casing. These will come out as one unit as they are banded or shrink-wrapped together.
-
Locate the point where the wires run from the terminal piece down through the silver cardboard insulator. The terminal piece should be black or silver and located on top of the silver cardboard insulation, with the batteries beneath the cardboard. Mark the silver cardboard insulator at the exact point where the wires pass through the silver cardboard insulation. Again, this will make it easier to reassemble.
-
Release the terminal piece from the silver cardboard insulation using needle-nose pliers. Take care not to let the terminal wires touch or cross during this process as you are at risk for electrical shock or even an explosion. Set the terminal piece aside along with the battery case screws and spring.
-
Note the exposed metal band on the side of the battery pack. It is important to insulate this band with electrical tape prior to starting the process. This metal piece will be hot during the reconditioning process and insulating it with electrical tape will protect you from injury.
-
Remove the silver insulation piece that covers the top of the rechargeable battery cells. Place this piece aside to be used in reassembly.
-
Remove any plastic covering from the top section of the battery pack so you can access both the the top and bottom of the rechargeable battery leads.
-
Turn on the volt meter and set it to a reading of two volts. Check each individual battery cell and mark each battery cell that gives a reading of zero or negative. These will be the cells that will need to be reconditioned.
-
Prepare your external 12-volt power source, including alligator clamps, for the reconditioning process. Protect your hands, eyes and skin with protective clothing and safety gear during this potentially hazardous process.
- Learn to revive your drill battery.
Locate the positive and negative ends of the first battery to be reconditioned. The positive end will be raised and the negative ends will be flat.
-
From the 12-volt source, hold the black alligator clamp to the negative end of the battery and the red alligator clamp to the positive end for two seconds.
-
Release the clamps and use a battery test to see if the battery has been fully charged. Repeat the process if necessary. The rechargeable battery cell can be zapped up to 10 times. Continue reconditioning the remaining batteries.
-
Reassemble the battery pack.
About the Author
We are the huge battery company on sale laptop battery, laptop adapter, cordless drill battery, camcorder battery, camera battery, battery charger, mobile phone battery, PDA battery, two-way radio battery, all sell with price at rock bottom, 1 year warranty, 30 days money back, brand new, excellent customer service, 100% secure shopping guarantee.
If you are looking for a different item here are a list of related products on The Manual Edger, please check out the following: